jlj-qmk/keyboards/deltasplit75

DeltaSplit75

This readme and most of the code are from https://github.com/ahtn/tmk_keyboard/ and https://github.com/qmk/qmk_firmware/tree/master/keyboards/lets_split

Credit to ahtn and wootpatoot for work on the split keyboard firmware

Split keyboard firmware for Arduino Pro Micro or other ATmega32u4 based boards.

Case Files

Files are available here: https://github.com/xyxjj/DeltaSplit75-Case-files

Build Guide

The build guide should be found at https://qmk.fm/deltasplit75

First Time Setup

Download or clone the whole firmware and navigate to the keyboards/deltasplit75 directory. Once your dev env is setup, you'll be able to generate the .hex using:

make v2

or

make v2-YOUR_KEYMAP_NAME (if you make a folder for your keymap)

or

make protosplit (if you have one of the prototype PCBs)

You will see a lot of output and if everything worked correctly you will see the built hex files:

deltasplit75_v2_protosplit.hex 

or

deltasplit74_v2_YOUR_KEYMAP_NAME.hex

or

deltasplit75_v2_default.hex

For more information on customizing keymaps, take a look at the primary documentation for Customizing Your Keymap in the main readme.md.

DeltaSplit75 V2

The PCBs available in groupbuy are all v2, if you've bought one of my prototype PCBs (it says DeltaSplit65 on the silkscreen instead of 75), use the code make protosplit instead

Features

For the full Quantum Mechanical Keyboard feature list, see the parent readme.md.

Some features supported by the firmware:

• Either half can connect to the computer via USB, or both halves can be used independently.
• 75% formfactor
• Support for multiple Bottom Rows
• RGB underglow support
• Split Backspace and ISO support

Flashing

I personally use xLoader to upload my hex files to the keyboard, though any other working software is fine too

Choosing which board to plug the USB cable into (choosing Master)

Because the two boards are identical, the firmware has logic to differentiate the left and right board.

It uses two strategies to figure things out: look at the EEPROM (memory on the chip) or looks if the current board has the usb cable.

The EEPROM approach requires additional setup (flashing the eeeprom) but allows you to swap the usb cable to either side.

The USB cable approach is easier to setup and if you just want the usb cable on the left board, you do not need to do anything extra.

Setting the left hand as master

If you always plug the usb cable into the left board, nothing extra is needed as this is the default. Comment out EE_HANDS and comment out I2C_MASTER_RIGHT or MASTER_RIGHT if for some reason it was set.

Setting the right hand as master

If you always plug the usb cable into the right board, add an extra flag to your config.h

 #define MASTER_RIGHT

Setting EE_hands to use either hands as master

If you define EE_HANDS in your config.h, you will need to set the EEPROM for the left and right halves.

The EEPROM is used to store whether the half is left handed or right handed. This makes it so that the same firmware file will run on both hands instead of having to flash left and right handed versions of the firmware to each half. To flash the EEPROM file for the left half run:

avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-lefthand.eep
// or the equivalent in dfu-programmer

and similarly for right half

avrdude -p atmega32u4 -P $(COM_PORT) -c avr109 -U eeprom:w:eeprom-righhand.eep
// or the equivalent in dfu-programmer

NOTE: replace $(COM_PORT) with the port of your device (e.g. /dev/ttyACM0)

After you have flashed the EEPROM, you then need to set EE_HANDS in your config.h, rebuild the hex files and reflash.

Note that you need to program both halves, but you have the option of using different keymaps for each half. You could program the left half with a QWERTY layout and the right half with a Colemak layout using bootmagic's default layout option. Then if you connect the left half to a computer by USB the keyboard will use QWERTY and Colemak when the right half is connected.

Notes on Using Pro Micro 3.3V

Do update the F_CPU parameter in rules.mk to 8000000 which reflects the frequency on the 3.3V board.

Also, if the slave board is producing weird characters in certain columns, update the following line in matrix.c to the following:

// _delay_us(30);  // without this wait read unstable value.
_delay_us(300);  // without this wait read unstable value.